diameter

No items matching your keywords were found.

Screw Extractor Guide pt 2

This is part two of a series on screw extractors. These are handy little tools that come quite in handy any time you have a screw head that has become stripped out or that has broken off, or if you have a bolt that has a head that has become stripped or broken off. Without [...]

Online Stores Blog Traffic Exchange Related Posts
  • lockHow to Install New Locks in Your Doors If you need to install new locks on your doors, there's no need to call in a locksmith if you've got some basic DIY experience and you're pretty handy. Today's locks make it very easy to change them out and you won't need many tools to get the job done.......
  • lockwasherLots of Tool Tips Another Nutty Trick Let us say that you need to remove a nut with the use of an open end wrench but the wrench is too large for the nut. When you can do is insert a coin or a washer in between the nut and the wrench. The coin......
  • awlGuide to Measuring and Marking Tools pt 5 Awl and Center Punch Continued - The awl is generally designed to have flat sides on its handle which makes it difficult if not impossible for the tool to roll away while sitting on a workspace. You should never hit an awl with a mallet or a hammer. Hand pressure......
  • pressurewasherChoose the Best Pressure Washer for Your Needs The best pressure washer for you needs is the one that's affordable and does everything you need it to do. Pressure washers come in two types--those designed for residential use, and commercial models. Unless you plan to run a pressure washing business, you don't need a commercial model. And in......
  • screwdriverScrews and Screwdrivers 103 Having the right screwdriver on you can make most screwing jobs a lot simpler. A basic set of screwdrivers should include four standard slot tip screw drivers and four standard cross tip or Phillips screwdrivers, each with a different shaft length and a different blade size. Larger sets may contain......

Continue reading → Screw Extractor Guide pt 2

Fixing Warped Floors

Warped flooring is a major problem for many homeowners. First, it is typically caused by water damage, and can be indicative of a major leak, but it can also be caused by excessive wear, poor original materials or even chance. Warped floors are a bit of a hazard around the house and should be fixed [...]

Online Stores Blog Traffic Exchange Related Posts
  • pipeHow to Fix a Leaky Pipe Whether you're dealing with a slow drip, or you've got a gusher, a leaky pipe can be a serious problem. If the pipe is dripping on electrical wires, it can be even more dangerous. It is important to fix a leak as soon as you discover it. You can waste......
  • valuehomeEasy Ways to Increase The Value of Your Home As the housing market continues to struggle, many homeowners are looking into ways to increase the value of their homes. However, a common issue that keeps these homeowners from making improvement is the lack of availability on home improvement loans, and a lack of available funding. Luckily, there are many......
  • brokentableHow to Do Table Repairs There are many different ways that a table can get damaged, and when it is something so little it can be frustrating to have to replace because you don’t know how to fix it. Since most damage that occurs to a table is minimal, whether over time or a quick......
  • roofWinterizing Your Roof Before winter comes, there are a few things that you need to do to make sure that your roof will make it through one more season of rain and snow. While many of us are familiar with the tasks of cleaning out the eaves, there are quite a few other......
  • countertops3 Kitchen Countertop Surfaces Explained When it comes to renovating your kitchen, there are so many new options when it comes to counter tops that it can be a little intimidating to pick one. We're going to cover some of the most popular counter top surfaces to help make that decision a lot easier. This......

Continue reading → Fixing Warped Floors

The Basics of Drilling 4

Holding your Bits: If you want to keep your drill bits from bumping into one another and other tools, which could cost them their cutting edge in the process, then you should absolutely avoid storing them in any loose way. Instead, what you can do is either buy a bit holder from the hardware store [...]

Online Stores Blog Traffic Exchange Related Posts
  • bentbitThe Basics of Drilling 5 Buying a Drill: A good basic style electric drill is going to have a 3/8 inch chuck and VSR or variable speed reversing capabilities. Such a drill should be able to accept bits that have shanks up to the 3/8 inch point, and it should also allow you to control......
  • hammerEasy Tips for Better Hammering There is a multitude of different ways that you can improve your hammering, or just make working with a hammer easier for you. If you are into home improvement or wood working, then you probably end up working with a hammer a lot, and there is always room for improvement.......
  • stains-in-sinkHow to Get Rid of Unsightly Sink Stains Our sinks are subjected to constant abuse and even with the most careful cleaning, stains can occur over time. The most common stains are due to hard water and they can be difficult to remove. However, there are a few easy tips that you can use to get rid of......
  • crackedRepairing a Crack in the Driveway If you have a driveway that is made out of asphalt, then understanding the essentials behind driveway crack repair is going to be rather necessary. There are a number of benefits to using an asphalt driveway over one made out of gravel or dirt, including a longer lifespan and better......
  • cordlessdrillThe Basics of Drilling Hold the drill properly! If you want to drill a much straighter hole and to avoid breaking your drill bits, you need to hold the drill in such a way that the force you are exerting is going to help you push the bit directly straight into the wall. You......

Continue reading → The Basics of Drilling 4

The Basics of Drilling 3

Drilling without splinters! Drilling a hole completely through a piece of stock is going to leave an edge that is rough and splintery on the way out. In order to create a hole that is clean, you should look for the point of the bit as it is piercing through the back side of your [...]

Online Stores Blog Traffic Exchange Related Posts
  • interiorLearn How to Build a Wall You may end up with a remodeling project that involves learning how to build a wall in the interior of your home or another similar building. Building a nonbearing interior wall is actually a relatively easy process. If you have basic carpentry skills and a good set of working tools,......
  • paintingsuppliesPainting 101 Here are some things that you want to know in order to improve your capability for painting. Keep reading if you are planning a painting project and want to improve your chances of doing it successfully. Begin by taking off every switch and wall outlet cover. Tape the screw to......
  • awlGuide to Measuring and Marking Tools pt 5 Awl and Center Punch Continued - The awl is generally designed to have flat sides on its handle which makes it difficult if not impossible for the tool to roll away while sitting on a workspace. You should never hit an awl with a mallet or a hammer. Hand pressure......
  • pullHow to Choose and Install Cabinet Knobs and Pulls Cabinet knobs and pulls don't really get noticed much. At least, we've looked at our own for so many years we barely noticed them. It's something that's more easily noticed at someone else's house and at the home improvement store where there are dozens of different, eye-catching kinds. New cabinet......
  • Under Cabinet Lights in Remodeled KitchenHow Do I Install Under Cabinet Lighting I love my kitchen, I really do - it's just so dark over the countertops, which makes food preparation a bit dangerous. I've been looking into DIY under cabinet lighting options over the past couple of months and I think I've found a suitable option for our kitchen. Since we......

Continue reading → The Basics of Drilling 3

Email Updates